With the improvement of living standards, more and more household appliances are used in the home. In the installation of home appliances, if you do not make sufficient planning in advance, you may encounter the situation that the installation cannot be installed because there are not enough lines or locations reserved during the decoration. This is one of the most common decoration regrets of many homeowners. In order to avoid these regrets, you must pay attention to the installation of home appliances. So how to install home appliances? The following is a collection of various home appliance installation methods for you.
Air Conditioning Installation First determine the position of the inner and outer units, and install and fix the hanging plates of the inner and outer units. Then straighten the connecting pipe to keep the pipe straight, check whether the bell mouth has cracks, and if so, re-flaring. Check the line for open circuit, short circuit, etc. The two stood on the inside and outside of the wall to cooperate in inspections, bundling water outlets and pipes, etc. Remove the air from the ducts and the inner unit. Tighten the connected external unit first, and then use a wrench to loosen the valve stem of the globe valve; if the external unit makes a noise, wait for 30 seconds, then tighten it with a wrench; loosen the valve stem of the globe valve. Use detergent to pick up leaks, observe whether there are air bubbles in the joints, etc. If there are no problems, tighten the safety cap of the valve. Finally start the test run. TV installation The viewing distance of the wall-mounted TV should be at least 3 to 5 times the diagonal distance of the TV screen, and the installation height should be at the height of the owner sitting on a stool or sofa, with eyes looking at the center of the TV or slightly below. The best, the center point of the general TV is about 1.3 meters from the ground. After determining the installation position, mark the mounting holes of the hanger, and then drill holes in the marked positions. Then fix the hanger with screws etc. The back of some TVs needs to be assembled with the installation panel first, and then hung on the wall mount, while others can be directly hung on the mount and fastened with screws.
Washing Machine Installation Prepare the tools and materials required for installation, such as special faucets for washing machines, drain pipes, etc. Next, place the washing machine close to the power outlet, and then start connecting its water inlet pipe, one end to the washing machine’s water inlet valve, and the other to the faucet. Finally, connect the drain pipe to the drain port of the washing machine, connect the power supply and it is ready to use. Refrigerator installation First determine the installation position of the refrigerator, do not be too close to the wall, keep a distance of about 10 cm between the back and both sides, and leave a space of 30 cm at the top. Then level it after placing it, and after placing it, the refrigerator needs to be cleaned. The refrigerator that has just been delivered should not be powered on first. Generally, the refrigerator needs to be stationary for more than 2 hours before powering on. Installation of the air purifier Snap the handle on the top of the back cover to remove the back cover, slide the filter button to the far left, take out the dust filter, and take out the filter element. Remove the protective cover on the filter element, and put the filter element and dust filter back into the purifier in sequence. Slide the filter button to the far right and install the back cover. Take out the power cord from the bottom of the box, connect the power cord to the power port on the bottom of the purifier, and make sure that it is plugged in as far as it will go before turning on the power. Generally, the air purifier is placed in a lower place in the main activity area. Do not place the air purifier against the wall, and each side is more than 20 cm away from the wall. Water purifier installation Turn off the main water switch and disconnect the connecting water pipe under the faucet. Connect the electroplating ball valve to the side hole of the water inlet tee, and connect the two-point PE pipe to the outlet. The straight-through part of the water inlet tee is connected to the continuous water under the faucet, and the other straight-through part is connected to the water source. Connect the PE water pipe to the water outlet of the water purifier, and connect the other end of the pipe to the interface of the water purifier. Install the outlet faucet, and connect the PE water pipe to the tooth pipe at the lower end. Then connect the PE water pipe to the activated carbon water outlet after the water purifier. After unpacking the front three filter elements, put them into the corresponding filter shells, then disassemble the membrane tube, put in the membrane and tighten the end cap. Finally, insert the system power plug into the corresponding socket. Water dispenser installation For desktop computers, remove the transparent silicone plug at the bottom of the fuselage to allow water to flow out from the bottom. After cleaning, it can be put back, and the original fastened iron ring or cable does not need to be put back. The vertical water dispenser is divided into the vertical warm base unit and the vertical ice hot base unit: unscrew the nut after the body to drain the water, and then screw it back after completion. After cleaning, place the water dispenser in a cool place, place it horizontally, install a bucket, and connect to the power supply. Humidifier installation Turn the water tank over, unscrew the filter element counterclockwise, and then pour clean water into the water tank, I suggest using pure water or distilled water. And tighten the filter element assembly, wipe the body dry, and then install it, connect it to the power supply and it can be used normally. Wall fan installation First drill the holes on the wall according to the holes of the fixed triangle, and then install the screw to fix the triangle; insert the connector of the motor on the fixed triangle, and determine the direction of the motor Finally, tighten the screws; then install the grille and screws, connect the power supply and you are ready to use. Integrated stove installation First remove the gas panel, and then install the smoke chamber, pay attention to fixing screws at this time. After installing the top glass of the smoke chamber, install the previously removed gas panel, connect the power cord of the panel, put the fire cover and other accessories in place, and fasten the screws. Install the air source interface and the smoke pipe, pull out the smoke pipe from the bottom of the integrated stove, and fix it on the check valve previously installed on the wall with a hoop. Plug in the power cord and test the operation. The last step is to connect the air source. Here, you must test the air tightness of the air source. Generally, use soapy water to smear around the interface and observe carefully. After all installation is complete, carry out the ignition test. Installation of the range hood Disassemble the range hood, then take out the accessories, screw the plastic hole of the exhaust pipe with a screwdriver, and lock the protective cover on the range hood with the screw. Take out the range hood hanger and put it on the wall to make a mark first, then use an electric drill to drill holes in the wall, put the hanger on the wall, and fasten it with screws. Lift up the cooker hood, pay attention to the socket on the back of the cooker hood, and hang it on the wall rack. After the hood is hung up, put on the exhaust pipe. Then plug in the power supply, turn on the range hood and debug it again. Gas stove installation First use the template to determine the corresponding size and make holes in it, and then when connecting the gas stove, be sure to remove the plastic cover of the dust cap of the gas pipe joint, and check the air port If there is any blockage, tighten it with a pipe hoop to check for air leakage. Remove the positive plastic cover of the battery, and install it in the battery box to confirm the positive and negative poles. After the gas stove has been placed in a stable position, install the burner cover and pan support, making sure to lay it flat. Finally turn on the gas stove debugging. Installation of sterilization cabinet The sterilization cabinet should be smoothly installed in a place that is easy to operate and maintain, and should not be installed at an angle. Keep a safe distance of more than 15 cm from gas appliances and high-temperature open flames. Be sure to measure the installation space and the size of the disinfection cabinet first. Insert the disinfection cabinet smoothly into the set square hole and fix the position. Electric water heater installation After determining the location, you need to install the hook. During this process, you need to fix the hook firmly on the wall, and then hang the electric water heater on the hook just installed. When installing the water circuit, it is necessary to identify the position of the cold and hot water interface corresponding to the water heater, and clean the dirt in the pipe. When connecting water pipes, it is necessary to do a good job of sealing, and be sure to use sealing rings at the connection. Connect the water inlet to the safety valve, and then connect it to the domestic water pipe. Finally plug it in. Install the gas water heater to determine the installation location. The gas water heater should be about 1.5m away from the air. Use a screw gun to drill holes in the wall and install screws to fix the gas water heater. After installing the cold water valve and the hot water valve, install the gas valve. It is necessary to connect the intake pipe to the gas meter. Before installation, be sure to close the main intake valve and connect a three-way valve to the gas outlet of the gas meter. Install the exhaust pipe. Hang the gas water heater on the wall, screw in the screw at the punched position, seal the smoke pipe with aluminum foil, and then connect the water inlet, outlet, and gas pipes. After the whole installation is completed, check to see if it can be used normally, and check whether the gas pipeline is leaking. Yuba installation After the PVC ceiling in the bathroom at home is done, open the ventilation holes and install the ventilation windows. Determine the installation position of the Yuba, and the installation position of the Yuba should be directly above the bathtub or shower room. After removing the mask, connect the Yuba and the switch panel with a flexible wire, then connect the ventilation pipe, push the box into the air hole, fix the Yuba lamp, and finally install the mask back. Dryer installation First insert the connecting pipe and the positioning plastic strip into each other to fix; then insert the caster into the lower hole of the positioning plastic strip to form a lower support frame; open the cloth cover of the dryer and unzip the zipper , the four corner openings at the bottom of the cloth cover are aligned with the made pipes of the lower bracket, and the support pipes are respectively connected with 4 joints; the cloth cover is symmetrically sleeved on the direct top, and then the host is fixed on the host fixing frame, and installed in the Directly above and in the middle, fix the waterproof cover on the air outlet of the main unit with a nut; cover the cloth cover, do not cover the dry clothes on the air outlet of the main unit of the dryer, but hang them evenly and firmly on the clothes rail, and Close the zipper. Precautions for installation of household appliances: Do not operate with electricity: In order to prevent electric shock and protect personal safety, it should be reminded that the installation and operation of household appliances must be carried out under the condition of power failure and cannot be energized operate. After the installation is completed, it can be powered on and tested after checking that there is no problem. The electrical equipment with the live shell cannot be used and must be repaired in time, otherwise electric shock will occur and cause personal injury. Voltage to be calculated: Before installing household appliances, you must carefully check whether the operating voltage of the electrical equipment is consistent with the power supply voltage. Use must be equipped with a suitable transformer. Plan the maximum load of power supply In order to ensure the safety of electricity use and the normal performance of electrical equipment, each household appliance should have a separate power socket for power supply, and several electrical equipment should not share a multi-point socket to avoid causing Line overload and affect the performance of electrical equipment. Know the maximum current height Before installing electrical equipment, it is necessary to know whether the safe current-carrying capacity of the power supply line can meet the requirements for use, that is, the current-carrying capacity of the wires of the power supply line is not less than the working current of the electrical equipment. The working current of single-phase AC 220V electrical equipment can be estimated by dividing its rated power by the 220V voltage. Safety first When installing home appliances, safety must be the first. When the wire is broken, the power supply is cut off to avoid accidents and protect the safety of lines and electrical equipment.
