Lamp installation is also the last part of home decoration. Different spaces in home decoration will choose different lamps. After choosing lamps, many people do not know how to install them. If the lamp is not installed properly, it will be inconvenient to use in future life. There are many types of lamps, and the installation methods of different types of lamps are definitely different. Let’s take a look at the installation methods of ceiling lamps, chandeliers, mirror headlights and other lamps!
Ceiling lamp installation
1 , Use embedded bolts, nylon plugs or plastic plugs to fix, do not use wooden wedges. In order to ensure that the ceiling lamp is firmly and firmly fixed, and can prolong its service life
2. When shrinking bolts are fixed, the bolt specifications should be selected according to the technical requirements of the product, and the drilling diameter and embedment depth should be consistent with the bolt specifications. Consistent
3. There should not be less than 2 bolts or screws for each fixture, and the center of gravity of the fixture should be consistent with the center of gravity of the bolts or screws
4. Close The electric switch at home, disconnect the power supply, there are three small buttons next to the ceiling lamp socket, open and close the small buttons to fix the outer lampshade
5. The ceiling lamp cannot be directly installed on flammable objects Upper
LED chandelier installation
The installation height is generally between 2.2 and 3 meters from the ground. In special circumstances, it can be between 1.9 meters and 2.00 meters. Between two meters
Installation steps and precautions
1. Look at the size of the screw hole of the chandelier. After looking at the size, select the drill bit of the corresponding size and mark it.
2. Put the expansion screw on, and fix the hanging plate after fixing it.
3. Fix the suction cup. It is relatively simple to fix the suction cup. Use screws to link the suction cup and the hanging board together.
4. Link light body
5. Pay attention to the size, brightness and wiring of the living room, check the wiring conditions of the home, and see if it is suitable for installation in this position to ensure normal use
Ceiling fan light installation
Required tools screwdriver, masking tape, spare device, wiring nut
Installation steps and attention
1. To power off the circuit, please Remove the corresponding fuse or trip the corresponding circuit breaker
2. First, fix the hanger on the ceiling and use appropriate screws
3. Put the wave cup on the hanger , the power cord of the motor is led out from the inner hole of the boom, and then put the end of the boom with two holes into the lifting head of the motor, pierce the connecting bolt, lock the safety pin, and tighten the fixing screw
4. Hang the assembled motor on the hanger, and then connect the power cord. After connecting the wire, lock the wave cup to the hanger.
5. Fix the assembled fan blades to the on the motor, and tighten the fixing screws for inspection
6. Connect the power cord of the assembled light stand to the power cord left in the motor switch box, and then connect the light stand to the switch box, using Tighten the screws and install the lampshade
7. Check the screws, try turning them for 10 minutes, and check whether all the screws or coils are loose
Fluorescent tube installation
Required tools for engineering stairs , 1 electric pen, 1 screwdriver, 1 electrician
Installation steps and precautions
1. Power off the old lamps
2. Remove the Have an old mounting member with the light fixture in place, and disconnect the fluorescent light wires from the circuit wires
3. Use wire nuts and crimp-type solderless connectors to connect light fixture wires to line wires
4. Attach the light fixture to the ceiling and fasten with the screws provided with the new fluorescent light package
5. Note: LED comes with a constant current source, no ballast and starter are needed. When installing, you can remove the ballast and starter in the original bracket and install the lamp directly. Can
install the light bulb
1. Prepare a light bulb with a power of 40W. The common connection methods include screw and socket.
2. Use a herringbone ladder, it is best to have a helper to stabilize it. Ladder
3. Find the entry switch at home and pull the gate
4. Turn on the flashlight, hold the light bulb holder with one hand, hold the broken light bulb with the other hand, and unscrew it
p>
5. Then put on a new light bulb and tighten it.
6. Note: The insulation in humid environment should be done well. The light bulb is made of glass, and iron must be used when installing the hanger. Make the expansion screw (iron expansion pin), do not punch holes first.
Mirror headlight installation
The installation height is to install the bathroom cabinet, the mirror is above the bathroom cabinet, the highest position of the mirror is about 1.7 meters to 1.8 meters, so do not exceed 1.8 meters
Installation Steps and Notes
1. Determine the height of the bathroom and mirror, and determine the position of the mirror headlight
2. Draw a horizontal line on the wall to determine the position of the two screw holes
3. Use an electric drill to drill holes on the wall, and install the hanging board on the wall
4. Disconnect the power switch at home, and connect the reserved wire at home to the power cord of the lamp
5. Put the lamp on the hanging board, align the screw holes, and fasten the lamp.
6. Note: waterproof and anti-riot effect, carefully check whether the power cord is broken or not. Distinguish the input line at both ends of the light stand and the input line of the switch
Installation of the downlight
1. Preparations: check the outer packaging of the downlight to confirm that it is intact, determine the installation position in advance, and close the home Power supply
2. Before installation, a hole must be opened in the ceiling, and the size is determined according to the size of the downlight
3. Before inserting the downlight into the hole in the ceiling, it is necessary to install the hole in the downlight first. The wires are well connected
4. There will be springs at both ends of the downlight for fixing. By continuously debugging the springs, the height of the downlight can be determined and fixed.
5. After the bulb is fixed , and then break the light card, and then the downlight can be embedded in the hole.
6. Note: Confirm the applicable power supply before use, and be careful to avoid falling from high altitude, collision with hard objects, knocking, and do not lean against the wall Too close, the gas should not be too strong
Installation of spotlights
1. Determine the position of the spotlights. The spotlights are installed around the ceiling, which will stretch the distance between the wall and the ceiling, which will increase the space. Function
2. When installing the spotlight, be sure to install the transformer first, to effectively prevent the spotlight from exploding frequently, and use it more safely and at ease
3. Do it at the installation height of the spotlight Mark it, install the fixture track, and fix the spotlight stand on the track
4. After the installation is complete, power on the spotlight, and turn on the switch to adjust the angle
5. Note: Install an appropriate number of spotlights, pay attention to the size and distance of installation
Wall lamp installation
The installation height is 2240-2650mm from the ground, the bedroom can be closer to the ground, about 1400-1700mm, and the corridor exceeds the eye level About 1.8 meters high, under the working environment, the distance from the desktop is 1.4 ~ 1.8m
Installation steps and precautions
1. Determine the position of the wall lamp socket, and draw the wall lamp hanging plate hole position, easy to hit the expansion screw
2. Understand the layout of your own circuit, pay attention to the drilling depth
3. Insert the expansion screw into the hole, and use a hammer to drive the expansion screw in
4. Install the wall lamp hanging plate, pay attention to alternate sides to prevent offset
5. Install the hanging plate and the ceiling plate with screws, tighten and fix it, disconnect the power supply, and install the lamp body. Yes
6. Note: Pay attention to height, specification and wire color
LED light strip installation
※LED light strip installation diagram
Indoor installation
The back of each LED strip is affixed with self-adhesive 3M double-sided tape. When installing, you can directly tear off the sticker on the surface of the 3M double-sided tape, and then fix the light strip where it needs to be installed. , just press it flat with your hands
Outdoor installation
Outdoors will be exposed to wind and rain, and the use of viscose will easily make the LED light strip fall off. It is often fixed with a card slot. way, with the use of waterproof glue to consolidate the waterproof effect of the connection point
Connection distance
LED light with the longest connection distance, if it exceeds this distance, the LED light is easy to heat up, affecting The service life must be installed in accordance with the manufacturer’s requirements during installation, and the LED light strip should not be overloaded.
