[Drying bucket dehydrator failure] What to do if the drying bucket does not turn Five common faults and solutions of the dehydrator
There will be some problems when the dehydrator is in use Common faults, let me take an inventory of common faults and their corresponding repair methods.
The reason why the spin-drying bucket dehydrator does not rotate
1. The dryer motor holding brake on the washing machine is closed and not released in time; the washing machine can be turned off Remove the rear cover, and then open the door cover above the drying bucket to observe whether the brake inside is released; if the brake is normal and not released, check whether the connecting cable on the door cover is broken. , if there is a similar situation, reconnect the cable.
2. The dryer motor connector on the washing machine is difficult to rotate, such as lack of oil, damage, etc., which may cause the rotation of the dryer to fail. In this case, it is either refueling, or Just replace damaged parts.
3. Poor contact of the door switch of the dryer, biting off, etc., may cause the dryer to not work normally. At this time, the operation panel should be opened to check.
How to solve the problem that the spin-drying bucket dehydrator does not rotate
1. The power supply is not plugged in, and it is in a leakage situation. If it is still in the power-on state If it does not turn, it is necessary to see if the power leakage switch has tripped.
2. There are too many clothes on the drying bucket, and it cannot work properly if the load exceeds it, causing the inside of the washing machine to be stuck and unable to work normally; it can also be that there are items on the drying bucket squeezed .
3. The parts of the drum motor are damaged. The most common is the failure of the starting capacitor, which causes the internal circuit of the washing machine to fail. At this time, the damaged parts should be replaced in time.
4. If the belt at the bottom of the drying bucket is loose, tighten the belt or replace it with a new one.
What’s the matter with the spin-drying bucket dehydrator if the spin-drying bucket does not turn? How to solve it? If you find that the drying bucket does not turn, you can find out the corresponding reasons, and then take symptomatic solutions. If all the methods in the article are solved, and the spin-drying bucket of the washing machine still does not turn, then it is recommended to ask a professional master to check it, or take the washing machine to the after-sales inspection to see what the fault is. When the drying tub of the washing machine is seriously faulty, cannot work normally, and the maintenance cost is relatively large, it is recommended to replace the washing machine or dehydrator with a new one.
Usually, the dehydrator has the following minor faults:
1, the dehydrator does not work when the power is turned on;
strong>
Maintenance method: first, use a multimeter to measure whether the plug of the dehydrator is in good contact with the socket; after ensuring that the dehydrator still does not work after power-on, rotate the timer for a certain time, pull up the brake, and manually rotate the dehydrator If the dehydrator rotates normally and operates well, it can be judged that the capacitor is damaged. This is just to replace a capacitor of the same specification.
2, after manually rotating the dehydration bucket, it still does not work or does not work properly:
Usually there are the following 2 situations, we follow the actual comparison Just come and fix it.
1: The motor rotates but slowly.
Cause: Insufficient capacitor capacity or capacitor leakage, the motor dehydration bucket cannot hold the spindle and the brake is too tight.
Solution: Ask the owner of the dehydrator if the dehydrator can run quickly before it breaks down; if it can, the capacitor is leaking, and the capacitor of the same type can be replaced at this time. If it can’t run fast before, you need to replace a capacitor with a larger capacity. If there is a problem with the main shaft, you need to fix the main shaft and the dehydration bucket. If the brake is a problem, you can adjust the iron plate attached to the brake.
2: Motor does not move.
Causes:
1. Timer: Detection and solution: Rotate the timer to a certain position and observe whether the timer is normal. If it is not normal, it needs to be replaced If the timer is normal, cover the lid of the dehydrator, find out the two wires drawn by the timer, and use a multimeter to check whether the two wires are connected. If it is not connected, there is a problem with the timer. The timer is normal.
2. Capacitor: The solution is the same as if the motor rotates but the rotation speed is slow.
3. Motor: detection and solution: use the ohm gear of a multimeter to detect the two windings of the motor, one test lead is connected to the common end of the winding, and the other is connected to the other ends of the winding respectively. If the disconnection occurs, the motor winding is disconnected. At this time, you can check whether there is an external problem with the motor. If so, just connect the wire. If not, you can only replace the motor.
Five common faults of dehydrators and their solutions
First, the dehydrator vibrates too much, mainly due to uneven placement of dehydrated items, If some parts are loose, check whether the foundation is solid;
Second, after connecting the power, the inner tank does not turn, please check whether the starting tape is stained with oil, and it can be cleaned in time;
Third, the braking device fails or the braking time is too long. At this time, we should first check whether the screws of the brake joint are loose, and then check the wear of the lower tape and take corresponding measures;
Fourth, the drain pipe is blocked, this is simply to see if there is anything plugged in the water pipe, and clean it up;
Fifth, the bearing seat is hot, whether there is a problem with the lubrication , add a little lube and you’re done.
