How to adjust the drift in fishing
 1. Preliminary bottom search
After finding the fishing position, open the bait first according to the target fish, and use the bait Time is adjusted. First, hang a larger lead sheet on the lower hook to find the bottom. There may be a slurry layer on the bottom of the water. Hanging the lower hook to find the bottom is conducive to the accurate bottom finding, so that the floating sight is exposed to 1 eye, and the fishing point is the center of the circle with a radius of 15 cm. In the circle, try several times before and after, and fully grasp the underwater situation of the fishing spot.
2. Preliminary settings Adjustment
After the rough adjustment reaches the bottom, move the buoy down 15 cm, be sure to exceed the length of the predetermined adjustment, and trim the lead until the adjustment is 4.
3. Accurate bottom finding
This step is very important in the process of adjusting the bleaching. Remember not to pull the float up first, lower the hook and rub the single bait and cast the rod to see if the bait ball can make the float just submerge in the water, preferably in flat water. This bait is the ‘base bait’ that is the size of the bait group after finding the bottom. Remember the size of the bait group at this time.
After finding the ‘base bait’, move the buoy up 15 cm, and hook the base bait to find the bottom. I let the buoy show 4 meshes. After finding it, hang the ‘base bait’ on the hook and throw it out to see how many buoys are exposed at this time.
Assuming that 2 meshes are displayed at this time, we can know that the distance between the upper and lower hooks is about 2 meshes away from the displayed surface of the buoy, and these 2 meshes are the basis for us to judge whether the hook is off the bottom or not. . If I start fishing at this time, the bait must be less than or equal to the weight of the base bait, and some fine-tuning must be performed. Because if the slurry layer on the bottom is thick, the fishing target will definitely change. If the float is stable and the number of fishing items is greater than 4, it means that there is a slurry layer on the bottom of the water, and we need to move the buoy down to adjust the number of fishing items to 4.
At this time, the hook must hit the bottom and the upper hook is suspended. We can control the degree of the upper hook leaving the bottom by adjusting the size of the upper hook bait. If the fishing mesh is less than 4 meshes, it means that the bottom layer is thin. As long as the fishing mesh is between 2 and 4 meshes, the upper hook must be off the bottom and the lower hook must be bottomed. It is almost impossible for the fishing purpose to be less than 2. Fishing friends should have noticed that the above statement is based on ‘always one bait bottoms out’. Because Xiao Bian firmly believes that fishing must start from the bottom of the fishing principle, and then change the fishing head up and down according to the fish condition to adapt to the changes in the fish mouth.
4. Precisely adjust the fishing target to find the mouth
If the fish mouth is uncertain, we can make some adjustments to adjust. The first thing to note is that hand food is fixed! If you change your hand food, you need to recalibrate. If there is no fish in the mouth, I personally think it is the spirit of fishing. The method and size of the bait remain unchanged. We only need to move the buoy up to find the real mouth of the fish. ‘Bait bait’ cast the rod to see what is the difference between the fishing target and the fishing target just now. If the fishing target becomes smaller, it means that the hook is suspended, and remember this number, it will be hooked in the next fishing process. Whether it is floating or touching, you have a very good basis. If the fishing target remains unchanged, it means that both hooks are bottomed.
What are the precautions for fishing drift adjustment
1. The proportion of bait must be fully considered in drift adjustment, otherwise you will find it very difficult to find the bottom. As for bottom finding, if you don??t lower the fishing height, such as leveling 2-eye fishing, then you must use normal-sized bait to find the bottom, otherwise the inaccurate bottom finding will greatly affect the fishing.
2. Don’t be ruthless when trimming lead, but take it slow. Especially when it is time to reach the intended adjustment, you must trim it slowly, otherwise you will only be able to clip lead in the lead sheet if you cut too much. This leads to inaccurate float numbers and affects fishing.