How to use the hole punch binding machine
First, the binding method
When binding, press the presser foot handwheel Turn the presser foot clockwise to raise the presser foot, put the binding material under the presser foot, release the presser foot handwheel at the selected position and automatically press it, and then turn the presser foot handwheel counterclockwise ~180° to lock it, and then Rotate the staple handle counterclockwise and the staple goes through the material. When the penetration is in place, the lead arm will automatically hang the thread in the thread slot of the staple hook. At this time, the handle is lifted up. When the staple is withdrawn, the binding thread will follow through the binding material and release in a clockwise direction. Press the foot hand wheel to complete one stitch binding, repeat the above procedure, and the binding task can be completed immediately.
Second, upper stitching method
Loosen the fixing screw on the stitcher, remove the stitcher, and hang the hook at the end of the stitch Insert the stapler into the fixing hole of the stapler, keep it vertical, put the stapler into the original position of the stapler, and tighten the fixing screw on the stapler. There are many types of hot riveting binding machines, including manual, automatic, semi-automatic, and fully automatic binding machines. Although there are many models, their working principles are similar. In addition to the automatic binding machine, the general hot riveting binding machine can be roughly divided into the following two steps for binding.
Precautions for the use of hole punch binding machine
1. Before punching holes, remove pins, staples and other metal objects.
2. Before binding, please make sure that the glue has dried, and binding before the glue is dry will affect the life of the drill.
3. Try not to punch holes in the original hole if you are unskilled in using it, reserve a certain margin when binding, and don’t lean too far. When using a manual binding machine, pay attention to the length of the knife.
How to repair the common faults of the hole punch binding machine
When the hole punch binding machine has a binding alarm, first check whether the nylon tube of the binding machine is used up. If it is used up, we will replace the nylon tube. First, insert the through needle on the top of the binding machine from the feeding port, and gently rotate it clockwise 360° downward; secondly, put the remaining tube on the through needle, and go with the through needle from the feeding port. Pull out; finally, insert a new nylon tube and snap into place. It is worth noting that the nylon tube must be straight and cannot be bent, otherwise it cannot be used normally.
If the hole punch binding machine has a guard alarm, first check whether the guard is closed. At this time, we need to close the protective cover first, and continue to operate after the light goes out. Then lift up the protective cover and return it to its original position. If it still doesn’t work, check if the connection wire is off and desoldered. If the punch binding machine has a binding alarm failure, there will be three possible phenomena. Punched holes are clogged with scraps of paper. The drill bit is not properly installed in the drill sleeve. The binding paper has slipped out of the binding position. At this time, our maintenance method is as follows: remove the paper scraps in the voucher. Remove the drill bit, put it back in place, and tighten the nut. Rearrange the materials to be bound and then bind them.
In addition, when the punching and binding machine has a punching alarm failure, there may be several situations that need to be checked: check whether there is paper dust in the cavity of the drill bit; whether there is metal mixed in the bound paper certificate product; whether the use is too frequent, causing the drill to heat up; whether the drill is dull; whether the upper part of the drill is smooth. In view of these situations, the maintenance methods we can take are: open the protective cover, remove the drill bit, clean the drill bit cavity and the paper scraps in the drill sleeve. Check and remove staples, paper clips, or other metal foreign objects from vouchers and paper. not in service. Sharpen the drill bit. Press the “Down” button to make the drilling motor go down 2-3cm, open the transparent window on the upper part of the drill bit, and clean the internal paper scraps.
The punch binding machine is very useful to us, so we should use it in the correct way, and don’t wait until it is broken and then think about how to repair it. But sometimes it is not up to us to decide if the punching and binding machine is broken. If the above-mentioned fault occurs in the punching and binding machine, everyone can refer to the above methods for maintenance. I hope these methods can help everyone.
Declare: The above methods are derived from the program system index or shared by netizens. They are for your reference only and do not represent the research views of this website. sex and authority.
