As the weather turns cold, many homes have installed radiators to help them through the cold winter. The installation process of the radiator is not very complicated. Prepare the relevant tools and materials, and align the water inlet and outlet valves with the pipes. There are several ways for the radiator to enter and exit the water. The best installation location is under the window or where the air convection is better. So how to install a home radiator? Below are some schematic diagrams of radiator installation for you, I believe they can help you.
Radiator Installation Location Radiator Installation Location Selection
When choosing the location of the radiator, it is necessary to consider both the convection problem and the heating of cold air. Under normal circumstances, the radiator should be installed under the window sill, because the radiator is close to the ground, which can not only convect the indoor air, keep the room temperature balanced, but also heat the air that comes in through the crack of the window to prevent cold. effect.
1. The principle should be low and not high.
According to the principle of air, the hot air rises and the cold air sinks. The higher the radiator is installed, the greater the heat loss. Therefore, when choosing a location, both the convection problem and the heating cold air problem must be considered. 70% convection heat + 30% radiant heat, almost perfect welding distance and optimal volume design of convection heater, make the plate radiator have the best heat output rate. Under normal circumstances, the radiator should be installed under the window sill, because the radiator is close to the ground, which can not only convect the indoor air, keep the room temperature balanced, but also heat the air that comes in through the crack of the window to prevent cold. effect.
2. The principle of priority under the window
The installation position of the radiator under the window will not affect the placement of furniture, and it can effectively block the discomfort caused by the entry of cold air. However, the specific installation location should also consider the specific pattern of the customer’s home. The radiator has 6 different heights (300, 400, 500, 600, 750, 900) and 6 different models (P, PK, PP, PKKP, DKEK) to choose from to meet different needs.
What is the appropriate height of the radiator
1. If the wall-hung boiler is used for heating at home, it is recommended to buy a radiator below 1.6 meters, otherwise the pressure of the wall-hung boiler may not be enough and it may not be able to carry it, resulting in poor heat dissipation. The circulation is not good, the heating is not hot.
2. If the home is on the top floor, it is recommended to use a radiator with a short assembly, which also considers the heating pressure of the home, because if the high-level heating is used, the boiler of the heating company may not be able to reach the pressure, and then use High-combination radiators are even more difficult.
3. If it is the owner of the ground floor, it is recommended to use a high-plate radiator to prevent the explosion caused by excessive pressure. However, it is best to use a concealed installation when installing, otherwise, the radiator may Affects interior aesthetics.
4. For users in the middle and lower floors, high and low radiators generally do not have heating pressure problems, but considering the cost performance of radiators, it is recommended to use high radiators, because high radiators have higher heat dissipation rates. On the whole, it is more cost-effective than the short one. On the whole, the floor area of the home is reduced, and the occupied area is only the wall area.
Installation positions of radiators in different areas
Living room
The location of radiators in the living room is generally fixed, and can be placed on the two walls near the balcony or on one side of the sofa. Near the drying platform, it is conducive to air convection. At the same time, the distance between the radiator and the main pipe should not be too far, and the water flow resistance will not be too large within 2-3 meters, so as to avoid affecting the heat dissipation effect of the heating.
Dining Room
The installation location of the restaurant radiator is generally selected on the wall near the dining table, which can keep the dining area comfortable and warm, and can also create a beautiful dining environment in winter.
Bedroom
The installation position of the bedroom radiator should be as concealed as possible. It can be installed behind the bedroom door or under the window. Generally, it is recommended to install it under the bedroom window. On the one hand, it can effectively resist the invasion of outdoor cold air, and on the other hand, curtains can be used to hide the radiator as much as possible. At the same time, the installation position of the radiator in the bedroom should be a little away from the bed, because the radiator is too hot and too roasted to affect sleep, so try to install it at the foot position.
Study
The study is the area where radiators need to be installed most in the home. It is comfortable in winter, with a constant temperature and no noise, which is convenient for learning and avoids the noise interference of air-conditioning heating. The study radiator can be placed under the desk, or near the seat.
Bathroom
Bathroom radiators are generally placed above the toilet or near the bath.
Schematic diagram of radiator installation
Radiator installation Pre-engineering of radiator installation
1. The construction of the first phase of the heating project is after the wall renovation, before or after the construction of water and electricity and must be before the construction of other decoration processes conduct. Before the first phase of the heating project is completed and approved by the owner, other decoration processes will never be allowed to be constructed.
2. For the sake of appearance, if the heating installation is carried out before the decoration, the branch pipe connecting the heating main pipe and the radiator must be buried under the floor and in the wall, and can only be seen when connecting with the radiator. To the temperature control valve; in order to save trouble, many heating engineering construction workers directly leak the branch pipe from the ground to the ground to connect with the radiator, so that each group of radiators has two pipes leaking outside, which is not only unsightly but also easy to break. .
3. During the first phase of construction, pipe fixing and groove sealing must be carried out according to the number of radiators, the width of a single piece, the distance between pieces of radiators, the way of water inlet and outlet, and the center distance of the interface, as specified by the owner. Keep it accurate, otherwise it will affect the later radiator installation. At the end of the first phase of the project, the construction personnel can seal the groove only after the owner has passed the inspection at the site, and the first phase of the project is over. After the completion of the first phase of the heating project, the decoration workers must take care of the heating pipes and facilities during the decoration process, and must not move or damage them.
radiator installation steps Kitchen storage and kitchen storage
1. After determining the installation location of the radiator, when unpacking the radiator, be sure to carefully check whether the type, color and accessories of the radiator in the box are complete. Regular radiator manufacturers such as Jin flagship radiator provide standard accessories such as running air, wire plugs, expansion nails, and hooks for free.
Kitchen storage storage
2. Install the water inlet valve and the return water valve, which must be installed, do not ignore it to save money, otherwise it will be difficult to repair after the radiator fails.
Kitchen storage and storage
3. First, smash the expansion screws and hooks into the wall, and install the running air, wire plugs, and valves on the radiator (you can wrap some raw material tape in an appropriate amount), and then install the radiator. Put it on the hook.
Kitchen Storage Storage Kitchen Storage
4. Connect the valve to the pipe, and the radiator installation is successfully completed.
Requirements for pipeline installation or pipeline transformation
1. When selecting connecting pipes, special products for plumbing that have been tested and approved by relevant state departments should be selected. The working pressure of pipes and pipe fittings should be greater than the experimental pressure of the pipe network system. If the pressure of the pipe network cannot be determined, please select pipes and fittings with a pressure of 12kg/cm2. The curvature radius of the tube should not be less than 4D.
2. Control valves should be installed in each group of radiator inlet and return pipes, and the distance between the radiator extension and the riser should not be less than 200mm.
3. Pipe clamps should be installed every 300mm for exposed pipes.
4. If the pipe needs to pass through the wall, a casing must be installed.
Precautions for installation of radiator 1
Use a spirit level to correct the orientation of the radiator to fix the radiator pendant to ensure that the radiator is horizontal and vertical, and to ensure the precise connection between the pipe fitting and the radiator; Open the protective film inside the radiator to avoid damaging or scratching the paint film. When installing heavier radiators, ground brackets must be installed for support.
2
After the radiator is installed, it needs to be pressed. After the radiator is installed, it must be filled with water to test the pressure, and the pressure of about 10 kilograms must be pressed with a pressing machine to ensure that the radiator itself and each installation interface are free from leakage. leak. Some installation teams are lucky if they do not debug after the radiator is installed, which brings risks to the later operation of the system.
Three
Mixing radiators of various materials can cause malfunction. Experts clearly stated that installing radiators of different materials in the same system may damage the inner surface of the light radiator or destroy the protective layer; and the electronic potential is different, which may also cause water leakage; in addition, due to equipment changes, there are still operating disorders. hazard.
Four
When the radiator is installed, the aluminum-plastic pipes must be connected with joints and cannot be bent, otherwise it will easily lead to water leakage in the pipes. Each interface must be wrapped with hemp, and the interface and the aluminum-plastic pipe should be kept in the same horizontal position to avoid water pressure and pressure on the joint, resulting in leakage of the interface.
