1. Assembly method of throwing rod
1. The fishing
 line passes through the space bean (the space bean mainly controls the water depth. The position of the bean is moved to 1 meter from the fishing line).
2. The main line passes through the hollow lead sinker (the hollow lead sinker is mainly used for positioning, so as to avoid the electrons floating on the water surface).
3. The main line passes through the float slider (the red side faces the inside of the fishing line).
4. Put on the blocking beans and tie the knot (twice when tying the knot).
5. Hang the baited cage on the knotted place, and that’s it.
Second, The correct method of throwing a rod
1. Side throwing method
Side throwing method This is the most common method of throwing hooks. Usually used in windy conditions. The trick is to first hold the lead weight or sub-line with the left hand, place the hook bait on one side of the body, hold the rod handle lightly with the right hand, and use the body as the axis to roll the body from the left and the right Arms naturally swing up. You should try to fly as close as possible to the water surface with the lead sinker and hook bait to ensure that it swings into the front of the fishing spot accurately and lightly. The small size of the person swinging the pole and whether the advice of turning the body sideways is correct or not will directly affect the accuracy of the throwing hook.
2. Swing casting method
Swing casting method is a method of throwing the hook to the fishing spot like a swing. In the case of no wind and mild wind, this method of throwing hooks is often adopted: the trick is to hold the rod with the right hand first, the height is lower than the shoulder on the same level, the tip of the rod points to the fishing point, the left hand is pinched and dropped, and the hook bait is naturally hanging on the fishing point. the front of the player, and then raise the right arm to quietly swing the bait to the exact fishing spot. The hook bait and the lead sinker first enter the water, and then the buoy falls into the same drop point as the fishing sinker. Since there is no ring bamboo that presses the line and pulls back, this method is simple, convenient and practical.
3. Back-slinging method
The back-swinging method is usually used when the wind is relatively strong. The trick is to put the hook directly behind the body first. Dangling, when pulling a certain position, use vigorous force to throw it forward, like a horse-drawn carriage whipping a whip, when the rod moves forward, the hook bait and lead sinker are forced to the fishing spot. This series of actions needs to be neat and done in one go. This method of throwing hooks is generally not used, because the state of the bait is required to be hard or sticky when throwing. When encountering winds of about 4 or 5, other throwing methods are useless, so this method has to be used.
Third, how to use floats for casting rods
1. Choose the right floats
The floats are People have eyes, so the choice of float is generally small float for small fish, big float for big fish, small float for shallow water fish, and big float for deep water fish. However, because there are many types of floats, and each type of float is adapted to different fish conditions, it is necessary to experiment many times by yourself or through the introduction of others to make a good choice.
2. Adjustment of floats
We do not hang the sub-wires first, and then hang the heavy lead through the lead sheet seat. The weight of the lead sheet is greater than the floating Buoyancy, so that all the floats are submerged in the water, and finally the floats are gradually pulled up to the water surface, so that we can adjust the height of the floats by pulling the height out of the water surface.
3. Adjust the mesh adjustment
After the float is pulled down and thrown into the water, then gradually cut the lead sheet to reveal the desired mesh, the basic setting method That is: 7-mesh soft tail float (adjust 4-5 for 2 meshes), 7-mesh soft-tail float and pull bait (adjust 3-4 for 2 meshes), hard fine-tail rubbing bait (adjust 7-9 mesh, fish 2- 3 mesh.), hard and thin tail bait (adjust 5-7 mesh, 2-3 mesh.), the specific situation still has to be determined according to the weather, season, feed and hook, and fine-tuning can be done.
4. Find the bottom accurately
After we hang up the sub-line, we move the float, adjust the distance between the float position and the position of the space bean that has been positioned, and then move the float. Lower the hook and rub the bait and hang a large bait ball to find the bottom, so that the float is 2 meshes above the water surface. Finally, continue to pull the float up by about 2 cm. If the float shows more than 3 meshes, it means that the bottom has passed. Hang the bait ball of normal fishing size and throw the rod into the water, fine-tune the float until the fishing mesh is about 2 meshes for trial fishing.
5. Adjust the float during the trial fishing process
If the bait has a mouth, but no fish can be caught, it means that the fishing is too good, and the float is pulled up by 2CM. , If the mouth of the fish is on the mouth or the lower jaw, this is too blunt, and the float is 1 cm each time. If there is no fish mouth at the bottom of the fishing, you should pull down and float 15 cm at this time to find the water layer where the fish is.
6. Choose the right time
When the sun is strong during the day and the water is reflective, we can choose a more appropriate time, such as: When it is cloudy, or the sun is weak, or at night, etc., choose the right time for fishing.