How to use the commercial bean sprout machine
1. Disinfection
Before installing the machine, clean the machine and sprout basket For disinfection, use a watering can to sterilize the box with good disinfectant water. After spraying, artificially spray water to rinse the disinfectant. Put the budding basket into the good disinfectant water for immersion and disinfection, and rinse it with clean water after completion.
2. Bean selection
Choose good bean species specially used for the production of bean sprouts (sprout beans, the smaller the grain, the better ), select the deflated seeds, tender seeds, rotten beans, chipped beans, moth-eaten beans, and damp beans, disinfect the selected beans with good disinfectant water, soak them for 1-2 minutes, and then use Rinse with clean water (better rinse several times).
3. Soak beans
Put the selected beans in a sterilized container, soak them in 40-50°C warm water, (It is best to scald mung beans with 90°C hot water for 20-30 seconds to activate the vitality of the beans; it is best to use soybeans that have not passed the summer, and do not need to be scalded.) The specific operation is used according to the instructions and methods of the Kefa bean sprouts machine.
Under the condition that the ambient temperature is kept at 35°C, soak the green beans for 4 hours and soybeans for about 6 hours, observe whether the water absorbed by the beans during this period reaches saturation, and pay attention to the best Turn the beans every 2 hours to allow them to absorb water evenly (soybean water absorption rate is 107%, mung bean water absorption rate is 98%).
4. Installation
Put the soaked bean seeds into the sterilized germination basket. Put the bean seeds in the budding basket and put it on the machine bracket, close the machine door, and press once to manually pour water.
Commercial bean sprout machine operation tips
1. Box temperature adjustment
(1) Upper limit adjustment: turn the setting switch upwards, turn the setting knob high and low, the temperature displayed at this time is the high temperature alarm temperature in the box, when the temperature in the box reaches this temperature, the OFF red light is on, an alarm bell rings and forced watering is required (It is recommended to set the high temperature value: 35°C).
(2) Lower limit adjustment: turn the setting switch down, turn the setting knob to high and low, the temperature displayed at this time is the set temperature value in the box, when the temperature in the box is lower than this temperature, ON The green light is on, indicating that the machine is being heated (recommended to set the low temperature value: 22 ℃ ~ 23 ℃).
2. Water temperature adjustment
(1) Upper limit adjustment: Put the setting switch on the upper limit setting, and adjust the setting knob on the right side of it. This temperature is the high temperature alarm temperature. When the water temperature reaches this temperature for some reason, the water temperature alarm red light will be on and the alarm bell will sound (recommended to set the high temperature value: 35 ℃).
(2) Lower limit adjustment: put the setting switch at the bottom, it will display the water temperature setting temperature, adjust the knob on its right to set the water temperature, when the water temperature is lower than this temperature, the heating device It will automatically heat up, and the heating indicator green light is on. When the water temperature reaches this temperature, the heating device will automatically disconnect and maintain this temperature (refer to the mung bean sprouts set at 23 °C, and the soybean sprouts at 22 °C).
3. Watering interval adjustment
The adjustment buttons are arranged from left to right as percentages, ten points, and points. Generally speaking, mung bean sprouts take 240 minutes Once, soybean sprouts every 180 minutes. Assuming that it is set to 240 minutes, the display will be from 0 to 240 minutes at this time, and it will automatically spray water at 240 minutes, and it will cycle from 0 to 240 minutes after the water is sprayed.
Declare: The above methods are derived from the program system index or shared by netizens. They are for your reference only and do not represent the research views of this website. sex and authority.
