Now there are many types of ink cartridges on the market that allow refilling of other inks for continued use after the original ink cartridges are used. You can drill holes on the original ink cartridges; however, if you want to successfully ink tanks, you must pay attention to the following operations.
Can original ink cartridges be refilled?
Yes.
1. Ensure that the filled ink cartridges are intact; at present, the ink cartridges are rarely damaged in use in the market, but the user is re-installing the original ink cartridges When filling ink, you must learn to check the integrity of the ink cartridge; the specific inspection method is that if there is a lot of resistance or ink leakage when filling ink at the bottom, it means that the ink cartridge is likely to be damaged.
2. Try to use high-quality original ink for filling. If the user buys these fake inks, not only the use effect is not good Yes, and can also damage inkjet printers. Therefore, when you buy ink, if you really want to buy the original ink of the inkjet printer, I advise you to go to the repair center of the corresponding brand printer to buy it, and it is guaranteed to be true. If there is a real problem, the maintenance center also has a way to help you solve it;
3. Before refilling the ink, the original ink cartridge should be thoroughly cleaned, otherwise two different inks will occur Mixed use and produce chemical reaction, resulting in plugs and other failures. Many users often use the program to clean the ink cartridges that comes with the printer. In fact, this operation is not only time-consuming, but also not clean enough; the correct operation method is: when adding ink for the first time, unplug the three ink filling holes the piston, find a syringe, pour pure water into the ink cartridge, try not to let the water overflow, then hold the entire ink cartridge with your hand, make the ink filling hole upward, and shake it gently for a few times to fully dissolve the residual ink In the water added; if the force is too strong when shaking, the liquid inside may overflow. At this time, it should be dried with a paper towel or cloth in time to prevent it from spreading and infiltrating into the circuit board and causing hardware failure, and then use a syringe to remove The mixed liquid in the ink cartridge is pumped out, and this operation is repeated several times until the color of the extracted liquid is very light, and then use the program of cleaning the ink cartridge that comes with the printer to clean it.
What should I do if the ink cartridge is too much?
When filling the ink cartridge, be sure to use the proper amount; many users feel that filling the ink cartridge with ink, The operation is more cumbersome. In order to save trouble, many people either do not give the ink cartridge tank, but the tank is full; in fact, if the ink tank is excessive, it will not only cause the ink cartridge to leak ink during use, but also leak from the ink cartridge. The ink that comes out is very likely to wet the components inside the printer, which may cause a short circuit or even damage the printer! If you accidentally fill the ink cartridge with excessive ink, you must use some soft paper or other cotton cloth to gently absorb the ink cartridge and the nozzle in time to absorb the excess ink, but you must not wipe it back and forth with soft paper or other cotton cloth. The nozzle of the printer;
Which ink is better
Try to choose ink for filling, so that the effect after filling It would be a little better; since the inks on the market have ink and ink, the ink is oily, and the ink is water-based. Generally, the ink used in the original ink cartridges is ink, and the cheaper inks on the market are generally water-based inks. These inks are only ten to twenty yuan, while the substitute inks cost about fifty yuan; the printed handwriting after filling the ink , the outline is very clear;
Precautions for the use of printer ink cartridges
After filling the ink cartridges with ink, it is best not to put the ink cartridges back into the ink cartridges immediately In the rack, because many ink cartridges contain sponge pads for absorbing ink, and the sponge pad absorbs ink relatively slowly, after the ink tank enters the ink cartridge, it cannot be evenly absorbed by the sponge pad, so put the ink cartridge back into the ink cartridge It is a good idea to let the ink cartridge sit for a few minutes before placing it on the shelf to allow the ink to slowly penetrate all corners of the foam pad to ensure final print quality. On the contrary, if you put the canned ink cartridge back in the cartridge holder immediately, there will definitely be an air gap between the nozzle and the sponge pad, and this gap will make it difficult for the ink in the ink cartridge to flow smoothly from the nozzle. , so that when printing, there will often be broken lines or a certain color lack of color;
It should be avoided that the ink cartridge is exposed to the air for a long time to cause drying and clogging. The method of cleaning it; if the ink quality is relatively high, you should fill the ink cartridge immediately after the ink cartridge is filled, and print on the machine immediately after filling the ink; some ink will mix with the original ink remaining in the ink cartridge to produce some changes And block the nozzle; if the printer is not in use temporarily, you can also put the nozzle in a special nozzle storage box, in which the special rubber pad can block the air and keep the nozzle moisturizing for a long time;
If the ink cartridge and the The print heads are integrated, so when adding ink to the ink cartridge, you must pay attention to protect the nozzles on the ink cartridge from damage. Otherwise, once the nozzle is blocked or damaged, the ink cartridge cannot be reused. In addition, due to the frequent use of the ink cartridge, the print head may be blocked by the splashed paper fibers, resulting in poor output of the print head. Therefore, it is also necessary to clean the print head regularly; when cleaning the print head, try to use wet Gently clean the edge of the nozzle with paper towel and lint-free tissue without touching the nozzle, then use the cleaning button on the control panel of the inkjet printer to perform a cleaning action on the nozzle until the printout is clear;
When adding ink to inkjet printer cartridges, many primary users will choose to do it when the ink indicator indicates that the ink is exhausted; but for those old inkjet printers without ink indicator, they cannot follow the printer’s instructions. It’s time to change the ink, but most of these inkjet ink cartridges without ink indicator lights are transparent, so you can replace the ink by eye observation, specifically, observe the remaining amount of ink in the ink cartridge with your eyes. To judge when to add ink, usually fill the ink cartridge when there is still 10% of the ink remaining; if the remaining amount of ink cannot be observed, only the final printing effect can be observed, as long as there is a break in the printed page Line phenomenon should be to add ink to the ink cartridge.
